rattle can paint job rifle

Rattle Can Paint Job For my 1982 Toyota Pickup I am using Eastwoods Rust Converter for a base to neutralize the rust then going to spray an SEM High Build primer then will wet sand with 800. Dont use rattle cans.

Pin On Firearms

The handles that snap on the rattle can helps a bunch.

. If youre going to spray it yourself use a HVLP gun and automotive paint otherwise it wont hold up. Humidity will affect the rattle can paint. After proper prep work and the proper environment to spray paint the key is uniform paint thickness mills achieved by one person doing the painting knowing basic painting techniques and following the manufacturers directions.

Fog the first few coats on until you get a base allowing to. So you will hear us say stuff like Im gonna rattle can that gun which translates in common English to Im going to spray paint this gun camo. Buy the paint in a quart can and shoot it with a cheap gun.

Set up a raking shop light and watch for the paint and solvent to level out together and hit the wet look. SanDiegoJoeMemberfrom San Diego CA. Some solvents or degreasers may effect plastic or seals and some will leave behind a film that messes with paint.

And hose it down. The rattle can is named for the metal balls inside the can that mix up the liquid and create a distinct rattle sound when you shake the can. I dont play with 2 part paints to often and I feel its probably temp sensitive also.

Rattle up the basecoat paint can ball bearing for at least a minute and then lay it down. It is frustrating to paint a truck with rattle cans. I wait for a dry day heat the part or gun in front of a radiant heater and heat the cans in water hot from the tap that Ive put in a bucket.

Didnt work out too bad. The more you use it the more worn or experienced it looks. In this process I am.

Rattle can has held up for me on several rifles4make sure its clean before you paintof courseanother good tip is heat the paint can up to about 90 degrees for 5 minutes or soboiled water works the bestapply multiply thins coats for best results. The rattle can paint job features a long-lasting formula that covers 12 square feet in just one coat and dries to the touch in 20 minutes. The lower is an unspecified one filled out with a Palmetto State Armory lower build kit complete with buffer tube springs buffer.

When you need to mix 2 part stuff you have to find that ratio that works best for you and stay with in that manufacture zone for it to cure right. Camouflage like this is easy to clean off and change the color of your camo to fit the mission or environment. What some of these finishes offer is a much thinner finish vs average rattle can paints.

No need to strip any paint. These cans are pressurized like any can of spray paint and they can provide a nice air-dry coating on the firearm. In the 2nd amendment world we call it a rattle can.

Spray in a parallel line not a curved arc. Even a 20 spray gun will have at least twice the fan size of a spray bomb. My motorcycle only got maybe 2500 miles a year on it was garage kept and it looked horrible within a year of the new rattle can paint job.

This the the proper prepping phase of how to paint a rifle in order to get the best and most durable results without using spray paint. Ive seen some pretty nice rattle can paint jobs. Some products can be used over old finishes most cannot.

Its ideal for interior or exterior use on virtually any surface including wood plastic metal wicker plaster unglazed ceramic and more. My first attempt at painting an Ar15 with krylon or rustoleum canned spray paint. Buy your favorite can of denaturized alcohol acetone carb cleaner engine degreaser etc.

Unlike cerekote which requires stripping the paint and starting all over touch ups are a breeze. I used rope and ferns to add texture. For those of you who are looking for a more rugged look rattle can is the way to go.

About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. And getting an even layer around the forward assist bulgehousing was kind of a pain. It lays on flat and overtime gives you an awesome battle worn look.

Most enamals can be thinned with acetone about 3 to 1 and shot without much expertise. The gas block is an aluminum rail height one also from Skid Tactical. Do the prep right and youll have a nice low buck job thats easy to touch up.

The front sight is a UTG rail height fixed front sight I think the UTG code is MT-754X they make a rail height and gas block height one.

Pin On Firearms